Monthly Archives: May 2016

Cars Tires With Nitrogen

A member of the Dodge Challenger owners’ forum was buying a new car from a dealer and noticed green valve-stem caps on all four tires. The salesman told him that the tires had been filled with nitrogen, which would keep the tire pressure and temperature more consistent and that it would prevent tire rot from the inside out. It wasn’t a free add-on, though. The “nitrogen upgrade” was a $69 item on the supplemental window sticker. Another forum member later posted that his dealer was charging $179 for this same “upgrade.”

Some dealerships and tire stores claim that filling your tires with nitrogen will save you money on gas while offering better performance than air. But a closer look reveals that nitrogen has few benefits and much higher costs. For starters, a typical nitrogen fill-up will cost you about $6 per tire.

Why Nitrogen?
The Get Nitrogen Institute Web site says that with nitrogen tire inflation, drivers will note improvements in a vehicle’s handling, fuel efficiency and tire life. All this is achieved through better tire-pressure retention, improved fuel economy and cooler-running tire temperatures, the institute says.

This sounds great in theory but let’s take a closer look at each of those claims.

  • Better tire-pressure retention: Over time, a tire will gradually lose pressure. Changes in temperature will accelerate this. The general rule of thumb is a loss of 1 psi for every 10-degree rise or fall in temperature. The institute says that nitrogen has a more stable pressure, since it has larger molecules than oxygen that are less likely to seep through the permeable tire walls.In 2006, Consumer Reports conducted a year-long study to determine how much air loss was experienced in tires filled with nitrogen versus those filled with air. The results showed that nitrogen did reduce pressure loss over time, but it was only a 1.3 psi difference from air-filled tires. Among 31 pairs of tires, the average loss of air-filled tires was 3.5 psi from the initial 30 psi setting. Nitrogen-filled tires lost an average of 2.2 psi from the initial setting. Nitrogen won the test, but not by a significant margin.
  • Improved fuel economy: The EPA says that under-inflated tires can lower gas mileage by 0.3 percent for every 1 psi drop in pressure of all four tires. The theory is that since nitrogen loses pressure at a slower rate than air, you are more likely to be at the correct psi and therefore get better fuel economy.If you are proactive and check your tire pressure at least once a month, you can offset this difference with free air, and you won’t need expensive nitrogen. We think this invalidates the “better fuel economy with nitrogen” argument.

    For many people, however, this kind of maintenance is easier said than done. Most people either forget to regularly check and top off their tires, or never learned how to do it in the first place. Even Edmunds employees (typically a pretty car-savvy group) were under-inflating or over-inflating their tires, according to a tire-pressure study we conducted a few years ago.

    And though tire-pressure monitoring systems (TPMS) now come standard on cars, a 2009 National Highway Transportation Safety Administration (NHTSA) study found that only 57 percent of vehicles with TPMS had the correct tire pressure. That’s because most systems are only meant to signal that a tire has very low pressure, not to show that the pressure is optimal.

  • Cooler running temperatures: When air is pressurized, the humidity in it condenses to a liquid and collects in the air storage tank you use at the local gas station. When you add compressed air to the tire, the water comes along for the ride. As the tire heats up during driving, that water changes to a gas, which then expands, increasing tire pressure. Because nitrogen is dry, there is no water in the tire to contribute to pressure fluctuations.But this fluctuation in temperature isn’t as significant as you might think. A 2008 ExxonMobil studyplotted the changes in temperature over the course of various inflation pressures. The lines on the graph were virtually on top of each other. In other words, the change in temperature when using nitrogen was negligible.
  • Prevent wheel rot: Nitrogen proponents will also point out that water in a tire can lead to wheel rot. A tire engineer who anonymously maintains Barry’s Tire Tech, a blog on a number of tire issues, says this isn’t really a problem with modern cars.”Alloy wheels don’t really have a problem with water inside the tire,” the engineer writes in a post on nitrogen inflation. “They are coated to keep aluminum from forming aluminum oxide, which forms a crust, which isn’t very attractive. But even then, this crust protects the aluminum from further corrosion from the water.”

    Where wheels have problems is when the aluminum alloy contacts steel, such as the steel spring clip used on wheel weights. It’s a particular issue when salt is present, the engineer writes. “But this problem is totally independent of the inflation gas,” he says. “Steel wheels only have a problem if the paint is damaged.”

How to Repair Your Windshield the Right Way

images-12When faced with replacing a windshield, many car owners default to the lowest-price option. But if you take this route and are in a serious accident, your decision could cost you your life.

An incorrectly installed windshield could pop out in an accident, allowing the roof to cave in and crush the car’s occupants. Furthermore, when the front airbags deploy, they exert a tremendous force on the windshield and will blow out one that is not firmly glued in place.

“There are a lot of schlock operators” installing windshields, says Debra Levy, president of the Auto Glass Safety Council, which offers certification for installers. She says using original manufacturer’s glass is a plus, but choosing a good installer is even more important. To find a certified shop, visit Safewindshields.org and type your ZIP code into the box at the top of the page. Certification is valuable because it keeps installers up to date on advances in adhesives and changing automotive designs.

David Beck, one of two technicians at Windshield Express, near Salt Lake City, installs eight windshields a day and has been working in the auto glass business for 18 years. Beck agrees that certification is important and warns that there are many “tailgaters” — installers with no brick-and-mortar shop — who quickly “slam” windshields into cars with little regard for safety. They don’t handle the windshield correctly, don’t use the proper adhesives and leave the car unsafe for driving and prone to rusting and leaks.

“The thing I wish that drivers knew was that the windshield is the No. 1 safety restraint in your vehicle,” Beck says. The windshield is two sheets of glass held together by an inner layer of strong vinyl. When the windshield breaks, the vinyl holds the glass in place rather than allowing the shards to fall into the car and cut the occupants.

The windshield is a layer of protection that “keeps you inside the car and things out of the car,” Beck says. “This is not the place to cut corners on and go with the cheapest price.”

Steve Mazor, the Auto Club of Southern California’s chief automotive engineer, adds that if the windshield isn’t strong enough and an occupant is thrown from a speeding car, “the odds of survival are much less.” Thirty percent of all fatalities, he says, are due to people being ejected from the car.

An investigation by the ABC News program 20/20 on windshield safety shows technicians incorrectly installing windshields by not wearing gloves. The grease from their hands prevents the adhesives from bonding correctly, Beck explains. Another error that 20/20 caught was technicians failing to use all the necessary bonding agents, such as primer.

When you are looking for a good windshield installer, Levy recommends calling three shops and asking a few qualifying questions beyond just price and certification.

Levy says to ask the shops if they use original equipment glass, which is usually of higher quality and fits better. Also, she suggested asking how long the car should sit after the installation is complete. “If they say you can take the car right away, you should run in the opposite direction,” Levy says. A car should sit at least one hour before being driven and sometimes up to 12 hours, she says.

Beck says if you take your car to a dealership for a windshield replacement, it will just subcontract the job to a glass shop and then mark up the price about 30 percent. He recommends going directly to the glass shop to save money. However, when a car is new, the dealership might be the only place to stock the glass, as was the case for a 2011 Infiniti M56 Edmunds long-term test car where the windshield replacement cost $1,300.

Most windshield installation jobs take only about an hour and can be done at your home or office, Beck says. Once the installer is finished, check for signs that the job was completed correctly. Make sure the molding is straight and that there is no sign of adhesives visible inside the car, Beck says. The car should be clean inside. Debris or dirt left in your car could be the sign of sloppy workmanship, he says.

Should You Change Engine Coolant

For some vehicles, you’re advised to change the coolant every 30,000 miles. For others, changing the coolant isn’t even on the maintenance schedule.

For example, Hyundai says the coolant (what many refer to as “antifreeze”) in most of its models should be replaced after the first 60,000 miles, then every 30,000 miles after that. The interval is every 30,000 miles on some Mercedes-Benz models, but on others it’s 120,000 miles or 12 years. On still other Mercedes, it’s 150,000 miles or 15 years.

Some manufacturers recommend changing the coolant more often on vehicles subjected to “severe service,” such as frequent towing. The schedule for many Chevrolets, though, is to change it at 150,000 miles regardless of how the vehicle is driven.

Many service shops, though — including some at dealerships that sell cars with “lifetime” coolant say you should do it more often than the maintenance schedule recommends, such as every 30,000 or 50,000 miles.

Here’s why: Most vehicles use long-life engine coolant (usually a 50/50 mixture of antifreeze and water) that for several years will provide protection against boiling in hot weather and freezing in cold weather, with little or no maintenance. Modern vehicles also have longer intervals between fluid changes of all types partly because environmental regulators have pressured automakers to reduce the amount of waste fluids that have to be disposed of or recycled.

Coolant can deteriorate over time and should be tested to see if it’s still good, as it can be hard to tell just by appearances. Even if testing shows the cooling and antifreeze protection are still adequate, antifreeze can become more acidic over time and lose its rust-inhibiting properties, causing corrosion.

Corrosion can damage the radiator, water pump, thermostat and other parts of the cooling system, so the coolant in a vehicle with more than about 50,000 miles should be tested periodically. That’s to look for signs of rust and to make sure it has sufficient cooling and boiling protection, even if the cooling system seems to be working properly. It can be checked with test strips that measure acidity, and with a hydrometer that measures freezing and boiling protection.

If the corrosion inhibitors have deteriorated, the coolant should be changed. The cooling system might also need to be flushed to remove contaminants no matter what the maintenance schedule calls for or how many miles are on the odometer. On the other hand, if testing shows the coolant is still doing its job and not allowing corrosion, changing it more often than what the manufacturer recommends could be a waste of money.

Lets know that tires is so dangerous

the owner of a 1998 Ford Explorer in Georgia needed a new tire for his SUV and ended up buying a used one. When he was driving two weeks later, the tread suddenly separated from the tire. The Explorer went out of control and hit a motorcycle, killing its rider. An analysis of the used tire revealed that it was nearly 10 years old.

More recently, an investigation into the cause of the accident that killed the actor Paul Walker revealed that the Porsche Carrera GT in which he was riding had nine-year-old tires. The California Highway Patrol noted that the tires’ age might have compromised their drivability and handling characteristics, according to the Los Angeles Times.

These incidents illustrate not only the potential danger of buying used tires but also the perils of driving on aging tires — including those that have never spent a day on the road.

For years, people have relied on a tire’s tread depth to determine its condition. But the rubber compounds in a tire deteriorate with time, regardless of the condition of the tread. An old tire poses a safety hazard.

For some people, old tires might never be an issue. If you drive a typical number of miles, somewhere around 12,000-15,000 miles annually, a tire’s tread will wear out in three to four years, long before the rubber compound does. But if you only drive 6,000 miles a year, or have a car that you only drive on weekends, aging tires could be an issue. The age warning also applies to spare tires and “new” tires that have never been used but are old.

What Happens to a Tire as It Ages?
Sean Kane, president of Safety Research & Strategies, Inc., compares an aging tire to an old rubber band. “If you take a rubber band that’s been sitting around a long time and stretch it, you will start to see cracks in the rubber,” says Kane, whose organization is involved in research, analysis and advocacy on safety matters for the public and clients including attorneys, engineering firms, supplier companies, media and government.

That’s essentially what happens to a tire that’s put on a vehicle and driven. Cracks in the rubber begin to develop over time. They may appear on the surface and inside the tire as well. This cracking can eventually cause the steel belts in the tread to separate from the rest of the tire. An animation on the Safety Research & Strategies Web site shows how this happens. Improper maintenance and heat accelerate the process.

Every tire that’s on the road long enough will succumb to age. Tires that are rated for higher mileage have “anti-ozinant” chemical compounds built into the rubber that will slow the aging process, but nothing stops the effects of time on rubber, says Doug Gervin, Michelin’s director of product marketing for passenger cars and light trucks.

How Long Does a Tire Last?
Carmakers, tire makers and rubber manufacturers differ in their opinions about the lifespan of a tire. The National Highway Traffic Safety Administration (NHTSA) has no specific guidelines on tire aging and defers to the recommendations of carmakers and tire manufacturers. Carmakers such as Nissan and Mercedes-Benz tell consumers to replace tires six years after their production date, regardless of tread life. Tire manufacturers such as Continental and Michelin say a tire can last up to 10 years, provided you get annual tire inspections after the fifth year.

The Rubber Manufacturers Association says there is no way to put a date on when a tire “expires,” because such factors as heat, storage and conditions of use can dramatically reduce the life of a tire. Here’s more on each of these factors.

Heat: NHTSA research has found that tires age more quickly in warmer climates. NHTSA also found that environmental conditions like exposure to sunlight and coastal climates can hasten the aging process. People who live in warm weather and coastal states should keep this in mind when deciding whether they should retire a tire.

Storage: This applies to spare tires and tires that are sitting in a garage or shop. Consider how a spare tire lives its life. If you own a truck, the spare may be mounted underneath the vehicle, exposed to dirt and the elements.

If your spare is in the trunk, it’s as if it is “baking in a miniature oven,” says Dan Zielinski, senior vice president of public affairs for the Rubber Manufacturers Association. Most often, the spare never sees the light of day. But if the tire has been inflated and mounted on a wheel, it is technically “in service,” even if it’s never been used, Gervin says.

A tire that has not been mounted and is just sitting in a tire shop or your garage will age more slowly than one that has been put into service on a car. But it ages nonetheless.

Conditions of use: This refers to how the tire is treated. Is it properly inflated? Has it hit the curb too many times? Has it ever been repaired for a puncture? Tires on a car that’s only driven on the weekends will have a different aging pattern than those on a car that’s driven daily on the highway. All these factors contribute to how quickly or slowly a tire wears out.

Proper maintenance is the best thing a person can do to ensure a long tire life. Gervin recommends that you maintain proper air pressure in tires, have them rotated regularly and have them routinely inspected.

How To Determine the Age of a Tire
The sidewall of a tire is full of numbers and letters. They all mean something, but deciphering them can be a challenge. This Edmunds article about reading a tire’s sidewall goes into greater detail, but for the purposes of determining the age of a tire, you’ll just need to know its U.S. Department of Transportation (DOT) number.

Tires made after 2000 have a four-digit DOT code. The first two numbers represent the week in which the tire was made. The second two represent the year. A tire with a DOT code of 1109 was made in the 11th week of 2009. Tires with a three-digit code were made prior to 2000 and are trickier to decode. The first two digits still tell you the week, but the third digit tells you the year in the decade that it was created. The hard part is knowing what decade that was. Some tires made in the 1990s (but not all) have a triangle after the DOT code, denoting that decade. But for tires without that, a code of “328” could be from the 32nd week of 1988 — or 1978.

Clearly, these DOT numbers weren’t designed with the consumer in mind. They were originally put on tires to make it easier for NHTSA to recall tires and keep track of their manufacturing date.